|
For now the tool box latch is held shut with a wing nut and machine screw, I will probably go to a cotter key kind of thing. Thi
For now the tool box latch is held shut with a wing nut and machine screw, I will probably go to a cotter key kind of thing. This is a Craftsman 20" steel tool box. The tray is a little narrow though, I might bounce some tools from the tray down into
Date: 09/15/2004
Views: 547
|
The tool box is currently bolted to the bracket, until I decide how to hold it down, and be able to remove it quickly.
The tool box is currently bolted to the bracket, until I decide how to hold it down, and be able to remove it quickly.
Date: 09/15/2004
Views: 505
|
Just enough room to the side to allow use of the latches, and enough room to the back to clear the hood spring.
Just enough room to the side to allow use of the latches, and enough room to the back to clear the hood spring.
Date: 09/15/2004
Views: 511
|
TWindow washer pump relocated to radiator panel, next to the radiator
TWindow washer pump relocated to radiator panel, next to the radiator
Date: 09/15/2004
Views: 479
|
|
Nice tight fit on the bottom of the box. Next I have to make the brackets that will allow it to be bolted in.
Nice tight fit on the bottom of the box. Next I have to make the brackets that will allow it to be bolted in.
Date: 09/13/2004
Views: 483
|
After welding the pieces together, we found the frame shrunk, so we cut it in half, and welded a brace to it. It isn't perfectly
After welding the pieces together, we found the frame shrunk, so we cut it in half, and welded a brace to it. It isn't perfectly level since the toolbox's bottom is kind of deformed. I suggest making the final 45 degree cuts after welding the first 3 piec
Date: 09/13/2004
Views: 695
|
Toolbox frame, this will get bolted to the inner fender and the radiator support.
Toolbox frame, this will get bolted to the inner fender and the radiator support.
Date: 09/13/2004
Views: 502
|
That's a huge space for such a small item. Some owners put a 2nd battery there, but I want to get my noisy space using toolbox o
That's a huge space for such a small item. Some owners put a 2nd battery there, but I want to get my noisy space using toolbox out of the cab...
Date: 09/13/2004
Views: 527
|
|
It's the cheap carpet you buy in a 6ft roll from Walmart or Kmart for about $10-$11. All Totalled up, this console would cost ab
It's the cheap carpet you buy in a 6ft roll from Walmart or Kmart for about $10-$11. All Totalled up, this console would cost about $26-$30 to duplicate, minus the emblem of course.
Date: 09/10/2004
Views: 636
|
The new shift boot sure looks good with the new duct/console
The new shift boot sure looks good with the new duct/console
Date: 09/10/2004
Views: 519
|
If I had both of those emblems, I would have probably gone with a Bow tie emblem there.
If I had both of those emblems, I would have probably gone with a Bow tie emblem there.
Date: 09/10/2004
Views: 507
|
DONE!!
View from driver's side
DONE!!
View from driver's side
Date: 09/10/2004
Views: 462
|
|
yes, it does include a pop can, some PVC pipe, and card board, and a long piece of ABS plastic, but it flows air well.
yes, it does include a pop can, some PVC pipe, and card board, and a long piece of ABS plastic, but it flows air well.
Date: 09/09/2004
Views: 534
|
The "T" sticking through the housing of the duct.
The "T" sticking through the housing of the duct.
Date: 09/09/2004
Views: 511
|
This is the view the shifter would have of the connector
This is the view the shifter would have of the connector
Date: 09/09/2004
Views: 463
|
Here is how I am going to connect the duct to the heater. This was a PVC "T" fitting. the white part is the part I cut
Here is how I am going to connect the duct to the heater. This was a PVC "T" fitting. the white part is the part I cut off.
Date: 09/09/2004
Views: 468
|
